t_seriest

Technical Specifications

Dimensions

Head Dia.
1.24 inches (31.5 mm)
Body Dia.
1.0 inch (25.4 mm)
Length:
5.45 inches (138.5 mm)
Weight:
3.95 ounces (112 grams)1

Battery Type

  • 2xCR123A, 2xRCR123A, or 1x18650 li-ion2
  • Compatible battery diameter/length
    • 123A: (16-16.8mm/34-34.5mm)
    • 18650: (18-18.8mm/65-68.5mm)
  • Read battery safety precaution

Operating voltage

  • 2.7V - 8.4V

What's included

  • Spare O-rings
  • Battery magazine for two CR123A
  • User manual
  • Soft cigar holding grip
  • Lanyard ring attachment ring

Bundle kits

  • Kit
    • Includes all T100C2 Mark II base features and accessories, plus:
    • Mil-Spec paracord lanyard w/ quick attachment clip
    • Heavy duty nylon holsterw/ self-retention device and flip
  • Weapon kit
    • Includes all T100C2 Mark II kit features and accessories, plus:
    • Remote Pressure switch w/ separate on/off switch, Aluminum Weapon Rail Mount for 1" Body

Upgrade/replacement parts

  • Replacement:
    • Switch module

LED

  • CREE XM-L2 U2 LED (Cool White)
  • CREE XP-G S2 LED (Cool White)
  • CREE XP-E R3 LED (Cool White)

    • more LED options below

Max output

  • CREE XM-L2 U2:
    • LED lumen: 780
    • ANSI FL-14 lumen: 622
  • CREE XP-G S2:
    • LED lumen: 425
    • ANSI FL-14 lumen: 321
  • CREE XP-E R3:
    • LED lumen: 305
    • ANSI FL-14 lumen: 246

Beam Profile

  • CREE XM-L2 U2 LED
    • Center lux: x
    • Center spot angle: x°
    • Spill light angle: x°
    • Beam distance: x yards / x meters
  • CREE XP-G S2 LED
    • Center lux: 9700
    • Center spot angle: 5.2°
    • Spill light angle: 54°
    • Beam distance: 215 yards / 197 meters

Other LED options

  • CREE XM-L2 U2 LED (Neutral White)
  • CREE XP-G R4 LED (Neutral White)
  • CREE XP-E Q4 LED (Neutral White)
  • Osram Platinum Dragon 850nm Infrared (IR) LED

Lens

  • Impact resistance waterwhite glass lens with harden treatment
  • Anti-reflective (AR) coating

Circuit

  • C1800 DS current regulated circuit (XM-L2)
  • C1200 DS current regulated circuit (XP-G2 / XP-E)
    • Efficiency: up to 95%

Reflector

  • Smooth aluminum reflector

Material

  • HAIII hard anodization aerospace aluminum

Waterproof

  • IPX-8 standard

Output and Runtime

  • High and low brightness levels
  • XM-L2 U2
    • Led lumen: 780/111
    • ANSI FL-1 lumen: 622/88
    • Runtime: 1/12 hrs
  • XP-G S2
    • Led lumen: 425/68
    • ANSI FL-1 lumen: 321/58
    • Runtime: 1.7/15 hrs
  • XP-E R3
    • Led lumen: 305/60
    • ANSI FL-1 lumen: 246/50
    • Runtime: 1.7/15 hrs
  • Above runtime is performed by 2xCR123A. 18650 yields 50% longer runtime.

Operations

  • Tactical forward clicky switch
  • Basic
    • Turn on the light by pressing the tailcap button until it clicks.
    • Tight the head to enable the Turbo output mode, loose the head for general output mode.
    • You can pre-selected output level before turning on the light.

Controls

Carrying method

  • paracord lanyard with detachable lanyard holder (optional)
  • Rigid nylon holster w/ self retention device and flip (optional)

Other features

  • Rubber cigar grip
  • Battery reverse polarity protection
  • Tail stand ability with included tail stand boot (optional)

Warranty

Battery Safety Precaution

All EAGTAC flashlights are designed to use “button-top?battery (battery with protruding positive terminal). For rechargeable li-ion battery, use only EAGTAC li-ion battery, or other protected li-ion battery with compatible length and diameter. Before using the battery, check and ensure the battery outer wrapping (the isolating plastic film that wraps around the metal housing of the battery) is complete. Broken battery wrapping may lead to short circuit and damage to the flashlight.

Lithium and Li-ion battery can explode or cause burns if disassembled, shorted, or exposed to high temperature. Do not mix new and used batteries. Do not mix batteries with different brand, capacity, voltage, or install batteries backwards.

NiMH rechargeable battery may release gas during discharge. If you experience an inflated switch boot or find high pressure being built inside the flashlight, switch off the flashlight immediately. Slowly loosen the tail-cap to reduce the internal pressure and replace all batteries.     Back to top

Flashlight Maintenance

Periodically clean the threads and o-rings with a lint free cloth and apply a thin coating of EAGTAC synthetic grease to the o-rings and threads. After prolonged exposure to moisture, the head and batteries should be removed, inspected, and dried. Do not touch or attempt to clean the reflector, as it will scratch the reflective coating permanently.     Back to top

  1. Weight excluding battery
  2. All batteries must have protruding top button. All rechargeable li-ion batteries (e.g. RCR123A and 18650) should be equipped with internal protection circuit against over-charge,over-discharge, and short circuit.
  3. Beam output diameter taken at one meter
  4. ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured using a calibrated integrated sphere three minutes after turning on the flashlight. For O.T.F. lumen, measurement is taken one minute after turning on the flashlight.
  5. Turbo boost technology is activated every time you turn on at turbo output setting. It offers 20% more power to the LED for the first 200 seconds at turbo mode.
  6. Frequency: Strobe-100%-9Hz, Flash-100%-1.7Hz