t_seriest

Technical Specifications

Dimensions

Head Dia.
1.85 inches (47 mm)
Body Dia.
1.8 inches (45.5 mm)
Length:
5.5 inches (141 mm)
Weight
11.8 ounces (335 grams)1

Battery Type

Operating voltage

  • 5.4V - 19V
    • All batteries are connected in series. Do not exceed 19V. Do not use six 3.7V RCR123A.

What's included?

  • SX30L3 flashlight
    • Smooth aluminum black bezel.
    • Flat tail-cap (tail-stand)
  • Spare o-rings
  • User Manual
  • Mil-Spec Para-cord Lanyard w/ quick attachment clip
  • 3xCR123A Battery Magazines

Replaceable items

  • Lens

LED

  • CREE XHP70.2 P2 Cool White LED
  • CREE XHP70.2 Nuetral White LED

Max output

  • CREE XHP70.2 P2 Cool White LED
    • LED lumen: 4350
    • ANSI FL-14 lumen: 3610

Beam Profile

CREE XHP70.2 P2 Cool White LED

  • Center lux: 28,400 lux
  • Center spot angle: 12.6°
  • Spill light angle: 58°
  • Beam distance: 367 yards / 337 meters

Lens

  • Waterwhite glass lens w/ harden treatment
  • Anti-reflective (AR) coating on both side (96% transparency)

LED circuit

  • C5600 ST
    • Current regulated buck driver w/ efficiency of up to 93%
    • Wide voltage input range
    • Non-dimming constant current regulation for all output levels without flicking
    • Low battery voltage warning7
    • Energy saving feature5
    • Very low standby current (uA)

Reflector

  • Aluminum reflector with smooth coating

Material

  • HAIII hard anodization aerospace aluminum

Waterproof

  • IPX-8 standard

Carrying method

  • Para-cord lanyard

Battery arrangement

  • Innovative slot load design
  • No battery tray or battery magazine needed
  • Battery arragement design patent pending in United Status, Hong Kong, and China

Output and Runtime

  • Five brightness levels
    • Led lumen:
      43505-3400/2350/1115/430/8
    • ANSI FL-1 lumen:
      36105-2850/1970/945/365/6
    • Runtime:
      • 1.4/2.3/5.5/15/300 hours (3x18650)6
      0.7/1.2/2.8/8.5/180 hours (6xCR123A)
  • Three hidden auxiliary outputs7
    • Disorienting Strobe/Beacon (1.67Hz)/S.O.S.
  • Testing above is performed by 3x18650. See other battery type runtime here.

Operations

Basic operations:
  • Turn on the light at MAX output by pressing the BLACK button switch. Turn on the light at LOWEST output by pressing the WHITE button switch
  • To turn off the light anytime, press and release the BLACK button switch.
Advanced:
  • For MAX output momentary on, press and hold the BLACK button switch for immediate output.
  • To switch between different brightness levels, press and release the WHITE button switch when the flashligh is on.

    (For example: if you want to turn on the flashlight at the 3rd level, just press and release the white button switch three times from off.)
  • To enter hidden auxiliary levels, press and hold the WHITE button switch when the flashligh is on.
  • For instant MAX output - at any output level, press and hold the BLACK button switch. Release the button to return to previous level.
  • For instant Strobe output - at any output level (even) off), double press and hold the BLACK button switch. Release the button to return to previous level (or off).
  • The optional switch button located at the tailcap is treated as the secondary BLACK switch button.

Controls

Other features

  • LED direct soldering on copper for maximum heatsink ability
  • User replaceable glass lens
  • Battery reverse polarity protection
  • Ultra low internal resistance phosphor bronze springs (silver coated)
  • Spring loaded positive and negative terminal
  • Tail stand
  • Tail-cap w/ switch for kit model

Warranty

Battery Safety Precaution

Ensure the protective circuit on the 18650 batteries has current limitation of higher than 8A. Always use proven EAGTAC batteries for best performance and reliability.

All EAGTAC flashlights are designed to use button-top battery (battery with protruding positive terminal). For rechargeable li-ion battery, use only EAGTAC li-ion battery, or other protected li-ion battery with compatible length and diameter. Before using the battery, check and ensure the battery outer wrapping (the isolating plastic film that wraps around the metal housing of the battery) is complete. Broken battery wrapping may lead to short circuit and damage to the flashlight.

Lithium and Li-ion battery can explode or cause burns if disassembled, shorted, or exposed to high temperature. Do not mix new and used batteries. Do not mix batteries with different brand, capacity, voltage, or install batteries backwards.

NiMH rechargeable battery may release gas during discharge. If you experience an inflated switch boot or find high pressure being built inside the flashlight, switch off the flashlight immediately. Slowly loosen the tail-cap to reduce the internal pressure and replace all batteries.     Back to top

Flashlight Maintenance

Periodically clean the threads and o-rings with a lint free cloth and apply a thin coating of EAGTAC synthetic grease to the o-rings and threads. After prolonged exposure to moisture, the head and batteries should be removed, inspected, and dried. Do not touch or attempt to clean the reflector, as it will scratch the reflective coating permanently.     Back to top

Other battery types runtime

Below lists the turbo output runtime with different battery types:

With energy saving enabled
(3xEAGTAC 3500mAh) 1.5hrs, (3xEAGTAC 2500mAh) 1hr, (6xCR123A) 0.8hr

With energy saving disabled
(3xEAGTAC 3500mAh) 1.3hrs, (3xEAGTAC 2500mAh) 0.9hr, (6xCR123A) 0.7hr

* Do not use six RCR123A as it may exceed the maximum voltage (i.e. 19V) that the LED driver can handle.
  1. This weight measurement is based on the Kit model excluding batteries
  2. All batteries must have protruding top button.
  3. Beam output diameter taken at one meter
  4. ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured with flashlight cold start-up using a calibrated integrated sphere.
  5. Energy saving feature reduce the maximum output current from 100% to 85% after 200 seconds at turbo output.
  6. Runtime is measured using three EAGTAC 3500mAh high discharge 18650 li-ion batteries.
  7. Maximum efficiency occurs when input voltage is very close to LED forward voltage.