g_seriest

Technical Specifications

Dimensions

Head Dia.
1.85 inches (47 mm)
Body Dia.
1.0 inch (25.4 mm)
Length:
6.1 inches (155 mm)
Weight:
5.9 ounces (167 grams)1

Battery Type

  • 2xCR123A, 2xRCR123A, or 1x18650 li-ion2
  • Compatible battery diameter/length
    • 123A: (16-16.8mm/34-34.5mm)
    • 18650: (18-18.8mm/67-68.5mm)
  • Read battery safety precaution

Operating voltage

  • 2.7V - 8.4V

Body color

  • Black (HAIII)

What's included

  • Spare O-rings
  • Titanium coated Stainless steel pocket clip
  • User manual
  • Soft cigar holding grip
  • Lanyard ring attachment ring
  • Mil-Spec paracord lanyard w/ quick attachment clip

Replaceable items

  • Lens
  • Switch module

LED

  • CREE XM-L2 U4 LED (Cool White)
  • CREE XM-L2 U2 LED (Neutral White)
  • CREE XP-L HI V3 LED (Cool White)
  • CREE XP-L HI V2 LED (Neutral White)

Max output

  • CREE XM-L2 U4:
    • LED lumen: 1278
    • ANSI FL-13 lumen: 1048
  • CREE XM-L2 U2:
    • LED lumen: 1116
    • ANSI FL-13 lumen: 915
  • CREE XP-L HI V3:
    • LED lumen: 1095
    • ANSI FL-13 lumen: 961

Beam Profile

  • CREE XM-L2 U4 LED (CW)
    • Center lux: 39,000 lux4
    • Center spot angle:6°
    • Spill light angle: 57.2°
    • Beam distance: 431 yards / 396 meters

  • CREE XM-L2 U2 LED (NW)
    • Center lux: 36,300 lux4
    • Center spot angle:6°
    • Spill light angle: 57.2°
    • Beam distance: 417 yards / 381 meters

  • CREE XP-L HI V3 LED (CW)
    • Center lux: 58,400 lux4
    • Center spot angle: 4°
    • Spill light angle: 54°
    • Beam distance: 527 yards / 483 meters

Lens

  • Waterwhite glass lens w/ harden treatment
  • Anti-reflective (AR) coating on both side (96% transparency)

Circuit

  • C3000 TS
    • Synchronous buck w/ efficiency of up to 95%
    • Non-dimming constant current regulation for all output levels without flicking
    • Low dropout voltage, enable circuit to current regulate even with a single 18650 for most of the runtime at turbo output.
    • Turbo boost technology

Reflector

  • Smooth aluminum reflector

Material

  • HAIII hard anodization aerospace aluminum

Waterproof

  • IPX-8 standard

Carrying method

  • Titanium coated stainless steel pocket clip
  • paracord lanyard with detachable lanyard holder

Other features

  • Tactical rubber cigar grip
  • Battery reverse polarity protection
  • User removable pocket clip
  • Tailcap battery stabilizer design to prevent battery movement inside the battery tube

Output and Runtime

  • CREE XM-L2 U4 LED
    • Led lumen: 12785-1202/366/40
    • ANSI FL-1 lumen: 10485-986/303/32
  • CREE XP-L HI V3 LED
    • Led lumen: 10955-1030/314/33
    • ANSI FL-1 lumen: 9615-896/270/26
  • Runtime:
    • 1.5/6/80 hours (1x18650)
    0.8/3.5/40 hours (2xCR123A)

Operations

  • Tactical forward clicky switch
    • Turn on the light by pressing the tailcap button until it clicks.
    • Twist the head to select between three output levels.
    • You can pre-selected output level before turning on the light.

Controls

Warranty & Maintenance

  • Ten years performance guaranteed warranty
  • Proper maintenance goes a long way to ensure your light to serve in the toughest environment and years to come.
  • Read below to how to keep your S200C2 in top shape.

Battery Safety Precaution

All EAGTAC flashlights are designed to use “button-top?battery (battery with protruding positive terminal). For rechargeable li-ion battery, use only EAGTAC li-ion battery, or other protected li-ion battery with compatible length and diameter. Before using the battery, check and ensure the battery outer wrapping (the isolating plastic film that wraps around the metal housing of the battery) is complete. Broken battery wrapping may lead to short circuit and damage to the flashlight.

Lithium and Li-ion battery can explode or cause burns if disassembled, shorted, or exposed to high temperature. Do not mix new and used batteries. Do not mix batteries with different brand, capacity, voltage, or install batteries backwards.

NiMH rechargeable battery may release gas during discharge. If you experience an inflated switch boot or find high pressure being built inside the flashlight, switch off the flashlight immediately. Slowly loosen the tail-cap to reduce the internal pressure and replace all batteries.     Back to top

Flashlight Maintenance

Cleaning: Periodically clean the thread and o-rings with a lint free cloth. Clean the battery contact, signal contact, thread, and body contact (conductive aluminum area) with a lint free cloth. Do not touch or attempt to clean the reflector, as it will scratch the reflective coating permanently

Lubing: Apply a thin coating of EAGTAC silicon-based lubricant to the o-rings (not the machined thread)and use a small drop of Deoxit red cleaner solution (D series) to slightly lube them for better conductivity and smoother mode switching experience.     Back to top
  1. Weight excluding battery
  2. All batteries must have protruding top button. All rechargeable li-ion batteries (e.g. RCR123A and 18650) should be equipped with internal protection circuit against over-charge,over-discharge, and short circuit.
  3. ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured using a calibrated integrated sphere three minutes after turning on the flashlight. For O.T.F. lumen, measurement is taken one minute after turning on the flashlight.
  4. Beam output diameter taken at one meter
  5. Maximum output current will be reduced from 100% to 90% after 200 seconds at turbo output to prolong turbo output runtime.