t_seriest

Technical Specifications

Dimensions

Head Dia.
0.55 inches (14 mm)
Body Dia.
0.5 inches (13 mm)
Length:
2.7 inches (70 mm)
Weight
0.4 ounces (13 grams)1

Battery Type

Operating voltage

  • 0.8V - 4.2V
  • Supports 1.2V NiMH, 1.5V alkaline, 1.5V(1.7V) lithium, 3.7V li-ion

What's included

  • D25AAA flashlight
  • Spare o-rings
  • User Manual
  • Stainless steel clip
  • Strong rare earth magnet (grey color coated)

Carrying method

  • Lanyard hole provided
  • Mirror finish stainless steel pocket clip
  • Magnetic tailcap

Waterproof

  • IPX-8 standard

LED

  • CREE XP-G2 Cool White S3 LED
  • Nichia 219B SW45 D220 LED (CRI 92) LED
  • 395nm UV LED

Max output

  • CREE XP-G2 S3 LED
    • LED lumen: 155
    • ANSI FL-14 lumen: 91
  • Nichia 219B SW45 D220 LED
    • LED lumen: 115
    • ANSI FL-14 lumen: 68
    • Color rendering index: 92
  • 395nm UV LED
    • Radiant Flux: 350mW

Beam Profile

  • CREE XP-G2 S2 LED

    • Center lux: 500 lux
    • Center spot angle: 19.3°
    • Spill light angle: 55°
    • Beam distance: 50 yards / 45 meters

    Beam Profile

  • Nichia 219B SW45 D220 LED

    • Center lux: 250 lux
    • Center spot angle: 19.9°
    • Spill light angle: 53°
    • Beam distance: 35 yards / 32 meters

    Lens

    • Waterwhite glass lens w/ harden treatment
    • Anti-reflective (AR) coating on both side (96% transparency)

    LED circuit

    • A300M
      • High switching frequency (1MHz) controller for more compact circuitry design
      • Low internal resistance design offers up to 90% efficiency7
      • Non-dimming constant current regulation for all output levels
      • Zero standby current
      • Supports output dimming with li-ion battery
      • Allows LED direct drive with li-ion battery at high mode

    Reflector

    • Optical grade acrylic TIR optics

    Material

    • HAIII hard anodization aerospace aluminum

    Output and Runtime

    • Three brightness levels
      • Led lumen: 1555/64/13
      • ANSI FL-1 lumen: 915/43/8
      • Runtime:
        • 0.7/1.3/6 hours (1xAAA)5

    Operations

    • Tight the head to turn on the flashlight. Loose the head to turn off the light.
    • Repeat the on/off action to cycle through three brightness levels, starting from low.
    • Cycle through two set of regular brightness levels to enter hidden auxiliary modes

    Controls

    Other features

    • Strong rare earth magnet installed at the tailcap (grey color coated)
    • Battery reverse polarity protection
    • Ultra low internal resistance phosphor bronze springs (silver coated)

    Warranty

    Battery Safety Precaution

    Ensure the protective circuit on the 18650 batteries has current limitation of higher than 5A. Always use proven EAGTAC batteries for best performance and reliability.

    All EAGTAC flashlights are designed to use button-top battery (battery with protruding positive terminal). For rechargeable li-ion battery, use only EAGTAC li-ion battery, or other protected li-ion battery with compatible length and diameter. Before using the battery, check and ensure the battery outer wrapping (the isolating plastic film that wraps around the metal housing of the battery) is complete. Broken battery wrapping may lead to short circuit and damage to the flashlight.

    Lithium and Li-ion battery can explode or cause burns if disassembled, shorted, or exposed to high temperature. Do not mix new and used batteries. Do not mix batteries with different brand, capacity, voltage, or install batteries backwards.

    NiMH rechargeable battery may release gas during discharge. If you experience an inflated switch boot or find high pressure being built inside the flashlight, switch off the flashlight immediately. Slowly loosen the tail-cap to reduce the internal pressure and replace all batteries.     Back to top

    Flashlight Maintenance

    Periodically clean the threads and o-rings with a lint free cloth and apply a thin coating of EAGTAC synthetic grease to the o-rings and threads. After prolonged exposure to moisture, the head and batteries should be removed, inspected, and dried. Do not touch or attempt to clean the reflector, as it will scratch the reflective coating permanently.     Back to top

    Other battery types runtime (MAX output)

    Sanyo Eneloop xx AAA 950mAh: 0.7hrs, Duracell alkaline: 0.3hrs, 10440 0.3hrs

    * When using 10440 li-ion, turn down the brightness when the light becomes too hot to touch.
    1. This weight measurement does not include batteries
    2. All batteries must have protruding top button.
    3. Beam output diameter taken at one meter
    4. ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured using a calibrated integrated sphere three minutes after turning on the flashlight. For O.T.F. lumen, measurement is taken one minute after turning on the flashlight.
    5. This lumen output and runtime is measured using Eneloop xx AAA 950mAh battery. Using 10440 li-ion at highest level will direct drive the LED at maximum output. Limit the operational time when using li-ion to prevent overheat.
    6. Runtime is measured with energy saving feature enabled using three EAGTAC 3400mAh batteries.
    7. Maximum efficiency occurs when input voltage is very close to LED forward voltage.