t_seriest

Technical Specifications

Dimensions

Head Dia.
0.9 inches (22.5 mm)
Body Dia.
0.8 inches (20 mm)
Length:
6.2 inches (157 mm)
Weight
2.4 ounces (72 grams)1

Battery Type

Operating voltage

  • 1.8V - 3.0V

What's included

  • D25A2 Tactical flashlight
  • Spare o-rings
  • User Manual
  • Mil-Spec Para-cord Lanyard w/ quick attachment clip
  • Stainless steel pocket clip (Titanium coated)
  • Heavy duty nylon holsterwith flip
  • User removable tailcap lanyard ring

Carrying method

  • Para-cord lanyard with quick attachment clip
  • User removable stainless steel pocket clip (Titanium coated)

Waterproof

  • IPX-8 standard

Replaceable items

  • Lens

LED

  • CREE XP-L HI Cool White V3 LED
  • CREE XM-L2 Cool White U4 LED
  • CREE XM-L2 Neutral White U2 LED
  • CREE XP-L HI Neutral White V2 LED

Max output

  • CREE XP-L HI V3 LED
    • LED lumen: 458
    • ANSI FL-14 lumen: 323
  • CREE XM-L2 U4 LED
    • LED lumen: 538
    • ANSI FL-14 lumen: 378
  • CREE XM-L2 U2 LED
    • LED lumen: 470
    • ANSI FL-14 lumen: 330

Beam Profile

  • CREE XM-L2 U2 LED

    • Center lux: 3,300 lux
    • Center spot angle: 11°
    • Spill light angle: 64°
    • Beam distance 125 yards / 114 meters

    Lens

    • Waterwhite glass lens w/ harden treatment
    • Anti-reflective (AR) coating on both side (96% transparency)

    LED circuit

    • A1000 TAC
      • High switching frequency (1MHz) controller for more compact circuitry design
      • Low internal resistance design offers up to 90% efficiency7
      • Non-dimming constant current regulation for all output levels
      • Zero standby current
      • Energy saving feature5

    Reflector

    • Very light textured aluminum reflector

    Material

    • HAIII hard anodization aerospace aluminum

    Output and Runtime

    • Four brightness levels
      • Led lumen: 5385-415/203/33/4
      • ANSI FL-1 lumen: 3785-295/145/25/3
      • Runtime:
        • 1.5/4.5/25/100+ hours6

    Operations

    • Tactical forward clicky switch
      • Turn on the light by pressing the tailcap button until it clicks.
      • Twist the head to select between three output levels.
      • To access the lowest 4th level, turn the head to 3rd level, then 2nd level, and then back to 3rd level within one second.
      • You can pre-selected output level before turning on the light.
      • Tail strobe feature (off by default): With this enabled, you can access strobe output at the tailcap switch button . To enable (or disable) this function (disable from factory), switch to 1st level and turn the flashlight on and off 20 times (one second or less between each click). With the tailcap strobe setting enabled, a double press of the switch button (within one second) will activate the strobe output.
      • Cycle through auxiliary modes: tight the head (1st level), and loose the head (3rd level) and then tight the head within one second to enter auxiliary setting. Repeat to cycle through all settings. Turn off the light or loose the head to quit.

    Controls

    Other features

    • User replaceable glass lens
    • Battery reverse polarity protection
    • Ultra low internal resistance phosphor bronze springs (silver coated)
    • Spring loaded positive and negative terminal

    Warranty

    Battery Safety Precaution

    NiMH rechargeable battery may release gas during discharge. If you experience an inflated switch boot or find high pressure being built inside the flashlight, switch off the flashlight immediately. Slowly loosen the tail-cap to reduce the internal pressure and replace all batteries.

    All EAGTAC flashlights are designed to use “button-top?battery (battery with protruding positive terminal). For rechargeable li-ion battery, use only EAGTAC li-ion battery, or other protected li-ion battery with compatible length and diameter. Before using the battery, check and ensure the battery outer wrapping (the isolating plastic film that wraps around the metal housing of the battery) is complete. Broken battery wrapping may lead to short circuit and damage to the flashlight.

    Lithium and Li-ion battery can explode or cause burns if disassembled, shorted, or exposed to high temperature. Do not mix new and used batteries. Do not mix batteries with different brand, capacity, voltage, or install batteries backwards.     Back to top

    Flashlight Maintenance

    Periodically clean the threads and o-rings with a lint free cloth and apply a thin coating of EAGTAC synthetic grease to the o-rings and threads. After prolonged exposure to moisture, the head and batteries should be removed, inspected, and dried. Do not touch or attempt to clean the reflector, as it will scratch the reflective coating permanently.     Back to top

    1. This weight measurement does not include batteries
    2. All batteries must have protruding top button.
    3. Beam output diameter taken at one meter
    4. ANSI FL-1 Lumens is a measurement of light output standardized by American National Standards Institute for use with flashlights. This ANSI Lumen measurement is the total overall light output being emitted from the flashlight. This measurement is generally more accurate as it takes into consideration the loss from reflector/lens/bezel. EAGTAC’s ANSI Lumen output is measured using a calibrated integrated sphere three minutes after turning on the flashlight. For O.T.F. lumen, measurement is taken one minute after turning on the flashlight.
    5. Energy saving feature reduce the maximum output current from 100% to 75% after 200 seconds at turbo output.
    6. Runtime is measured using two Sanyo Eneloop XX 2500mAh AA batteries.
    7. Maximum efficiency occurs when input voltage is very close to LED forward voltage.